Project overview
STM32H7-MC33816 is firmware and a CubeMX/CubeIDE project for the MC33816 fuel injector driver from NXP. The control board is a NUCLEO-H753ZI (STM32H753ZI) which talks to the KIT33816FRDMUG evaluation board over SPI. It serves as a reference platform for developing and testing injection control algorithms.
The MC33816 offers SPI configuration, peak-and-hold injector drive, advanced diagnostics and integrated protection. The STM32H7 provides the SPI master, the external clock, the injector start signals and the analog measurement.
Documentation
The repository contains the following documents in Documents/:
- NUCLEO-H753ZI schematics and user manual (UM2407)
- KIT33816FRDMUG user guide
- MC33816 datasheet
- Connection schematic between the Nucleo board and the kit
Hardware connections (NUCLEO-H753ZI -> KIT33816FRDMUG)
SPI interface
| Signal | STM32 pin | Kit pin | Note |
|---|---|---|---|
| SPI_MOSI | PA7 (SPI1_MOSI) |
MOSI | master out |
| SPI_MISO | PA6 (SPI1_MISO) |
MISO | master in |
| SPI_SCK | PA5 (SPI1_SCK) |
SCK | add a 2k7 pull-down |
| SPI_CS | PD14 |
CS | active low, software controlled |
Control and status signals
| Signal | STM32 pin | Kit pin | Note |
|---|---|---|---|
| MC_RST | PA4 |
RESET | reset, active low |
| MC_DRV | PB4 |
DRV_EN | driver enable |
| MC_IRQ | PE7 |
IRQ | interrupt, falling edge |
| MC_FLAG0 | PG14 |
FLAG0 | status flag |
| MC_FLAG1 | PF5 |
FLAG1 | status flag |
| MC_FLAG2 | PF4 |
FLAG2 | status flag |
| MC_FLAG3 | PG12 |
FLAG3 | status flag |
Clock, debug and analog inputs
| Signal | STM32 pin | Kit pin | Note |
|---|---|---|---|
| MC_CLK | PF6 (TIM16_CH1) |
CLK | external clock for the MC33816 |
| MC_DBG | PE8 |
DEBUG | debug signal |
| MC_OA_1 | PA0 (ADC1_INP16) |
OA_OUT1 | op-amp output 1 |
| MC_OA_2 | PA1 (ADC1_INP17) |
OA_OUT2 | op-amp output 2 |
The MC33816 outputs are 5 V while the STM32H7 ADC inputs are 3.3 V, so MC_OA_1 and MC_OA_2 need a voltage divider (5 V to 3 V).
Injector start signals
| Signal | STM32 pin | Kit pin |
|---|---|---|
| MC_START1 | PB9 |
START1 |
| MC_START2 | PB15 |
START2 |
| MC_START3 | PC7 |
START3 |
| MC_START4 | PB8 |
START4 |
| MC_START5 | PB12 |
START5 |
| MC_START6 | PC6 |
START6 |
Connect the grounds of both boards. The kit needs its own external supply for the high-current injector drivers.
Firmware configuration
From STM32H7-MC33816.ioc:
- MCU
STM32H753ZITx, Cortex-M7,SYSCLK = 480 MHz,HCLK = 240 MHz - SPI1 master, 8-bit, prescaler
/8, second clock edge (SPI_PHASE_2EDGE) - ADC1/ADC2 for the op-amp outputs, TIM16 for the MC33816 clock, TIM2/TIM5 as timers
- FreeRTOS with FPU enabled, stack overflow checking and run-time statistics
- Ethernet with LwIP (including
shell,ntp/sntp,pingandperfmodules), mbedTLS, USB device, RTC, RNG, CRC, CRYP and HASH
Repository structure
Core/- application sources (main.c,freertos.c,adc.c,rtc.c,debug.c,dwt_delay.c)Drivers/- HAL, CMSIS and BSPLWIP/,MBEDTLS/,Middlewares/- network and security stackUSB_DEVICE/- USB device stackweb/- web assets served by the embedded HTTP serverDocuments/- schematics, manuals and datasheets
Build, flash, and test
- Clone
https://github.com/CodElecCz/STM32H7-MC33816 - Open
STM32H7-MC33816.iocor import the project into STM32CubeIDE - Regenerate code in CubeMX if needed and build Debug or Release
- Flash through ST-LINK using the included
.launchconfigurations - Wire the boards as described above and check the SPI and signal levels
Verify the pin assignment against the .ioc file before connecting hardware, and check the SPI timing against the MC33816 datasheet.
Image placeholders
